Most houses on the North Shore, in Vancouver and in Burnaby still run on the perimeter drain they were built with. On a house from the 1950s to the early 1980s that is usually clay tile or unlined concrete pipe, laid beside the footing and never looked at since. Those drains silt up, crack under decades of soil load, and fill with roots from the cedars and maples that make these streets what they are. When the drain stops carrying water away from the footing, the water goes where it can: through the wall, under the slab, into the crawlspace.
Signs the perimeter drain is failing
- Water or damp patches at the base of a basement wall after a day of heavy rain, not during it. The delay is the drain backing up.
- A white, chalky bloom on concrete or block. That is efflorescence, minerals left behind as water passes through the wall and evaporates.
- A musty smell, a dehumidifier that never catches up, or condensation on cold-water pipes in summer.
- Standing water in window wells, or a sump that runs constantly through the winter and never in August.
- A basement slab that has cracked, lifted or stays dark in one corner.
- Downspouts that disappear into the ground into a drain nobody has flushed in living memory.
Why drains fail here
Metro Vancouver gets most of its rain between October and March, and the North Shore mountains get far more of it than Richmond or Delta. A drain that copes in July is tested hard every winter. The usual failures are ordinary: the pipe has silted up, roots have grown in through the joints, a section has been crushed or has separated, or the downspouts were tied into the same undersized drain with no leaf protection at the top. Grading matters too. Soil settles toward the house over the years, and a lawn that once shed water away from the foundation now delivers it there.
What the assessment covers
- Camera inspection. We run a camera through the drain from the cleanouts and record what we find: silt, roots, breaks, bellies where water sits, and where the drain connects to the storm system.
- Flush test. Water into the downspouts and drain, and we watch how fast it moves and where it comes out. This finds the section that is not carrying flow.
- Grade, wells and downspouts. We check the slope of the soil at the foundation, every window well, and where each downspout actually goes.
- Inside. Moisture readings on the walls and slab, and a look at the sump if there is one.
- Written scope. A plain-language summary with the camera stills, a red, yellow and green finding for each zone, and the repair options with a fixed price for each. It is yours to keep whether or not you hire us.
How we repair it
The right fix is the smallest one that will hold. In order of scope:
Flush and clear
If the pipe is intact and the problem is silt or roots, a high-pressure flush and root cutting restores flow. We re-scope afterwards to confirm it, and we will tell you if the roots are coming back next year because the joints are open.
Spot repair
A crushed or separated section can often be excavated and replaced on its own, with the rest of the run left alone. This is common where a driveway, a tree or a past renovation has damaged one length of pipe.
Full replacement
When the drain has failed along its length, we excavate to the footing, install new perforated PVC drain pipe in filter fabric and clean drain rock, clean and damp-proof or waterproof the foundation wall, add a drainage membrane against the wall, and tie the downspouts into their own solid pipe so roof water never enters the perimeter drain again. Backfill, compaction and reinstatement of the surface are part of the scope, not an extra.
Interior systems
Some walls cannot be dug: a shared wall, a deck on posts, a house built to the property line. For those, an interior perimeter channel cut into the slab edge collects water at the footing and carries it to a sump with a pump. Where the municipal storm connection can back up, a backwater valve and a battery-backed pump protect the basement when the power goes out in a storm, which is when you need it.
Depth to the footing, access for an excavator versus hand digging, what has to come up and go back (concrete, patio, deck, landscaping), the length of the run, soil conditions, and whether the municipal storm connection needs to be renewed and inspected. Each option in your scope is priced fixed, with these items listed so you can see what drives the number.
Permits and the municipal connection
Work on the drain tile and its connection to the municipal storm sewer is regulated by each municipality, and some require a permit and an inspection before backfill. We handle the application and the inspection booking as part of the job and note in the scope where a permit applies.
Warranty
Drainage and envelope work carry our longest workmanship warranty. The term is written into the scope you sign, not a brochure.